Product added to cart
Ultra-Twin IBC Hard Top Pallet With Drain
$4,908.33
In stock
SKU
SP1149
- Ultra-Twin IBC Hard Top Spill Pallet With Drain - 128" x 67" x 96"
- For use in storing two IBC tank when secure outdoor storage is needed, along with remaining in compliance with EPA regulations.
The Ultra-Twin IBC Spill Pallet provides storage and spill containment for IBCs, tanks and other large containers. The pallet is economical as two IBC tanks could be stored side-by-side on it. The large, 535-gallon spill containment sump meets EPA and SPCC spill containment regulations for two IBC tanks. Add optional bucket shelves to catch drips and leaks from dispensing spouts. The all-polyethylene construction provides excellent chemical compatibility.
Comply with spill containment regulations while storing IBC tanks outdoors
Store two IBC tanks outdoors and keep them safely out of the elements while providing enough containment to meet EPA and SPCC spill containment regulations. The covered containment will also help to meet the NPDES requirements.
Key Features:
• Uses the same sump as Ultra-Twin IBC Spill Pallet
• Unique, lockable, dual closure allows quick access to IBC tanks or drums
• Heavy duty construction can handle up to 8,000 lbs. per side (UDL).
• Roll-top covers can be easily lifted for routine visual inspection
• UV inhibitor in polyethylene resin resists degrading effects of sunlight, adding years to outdoor service life.
• Swing-out doors provide safety and convenience for loading/unloading tanks
• Safely stores IBC tanks with maximum dimensions of 52" x 52" x 61".
Compliance:
- EPA Container Storage Regulation 40 CFR 264.175
- Spill Prevention, Control and Countermeasure Act (SPCC) 40 CFR 112
- Stormwater Management Regulation 40 CFR 122.26
- National Pollutant Discharge Elimination System (NPDES)
Warranty:
• Protected by the industry’s strongest warranty - Five (5) years against any material or workmanship defects.
Specifications:
Dimensions: 128" x 67" x 96"
Uniformly Distributed Load: 8,000 lbs/side
Containment Capacity: 535 Gallons
Weight: 1,067 lbs
Options: Ultra-Bucket Shelf (Part#1160)
| Brand | UltraTech |
|---|---|
| Type | IBC Hard Top Spill Pallet |
| Drain | With Drain |
| Dimensions | 128" x 67" x 96" |
| EPA Compliant | Yes |
| SPCC Compliant | Yes |
| Stormwater Management Regulation Compliant | Yes |
| NPDES Compliant | Yes |
| Material | Polyethylene with UV inhibitors |
| Load Capacity | 8000 lbs/side |
| Sump Capacity | 535 gal |
| Features | Roll-top Covers |
| Duty Type | Heavy Duty |
Assembly Instructions
Step 1: Center Wall Preparation
Inspect black center wall. If tabs are in place, they will need to be cut to be flush the bottom surface of the wall.
This can be done with a circular saw, jig saw or reciprocating saw.
Step 2: Center Wall Preparation
Install interior wall nut assemblies in the corners at the top and bottom of the center wall.
Step 3: Organizing All Thread
IMPORTANT: Not all the pieces of all thread are used in the assembly of the Twin IBC Hard Top.
You will receive thirteen (13) pieces of all thread but will only need eight (8) pieces (four pieces with black plastic sleeves and four without). Four of these pieces (two with black plastic and two without) are 56 1/2”. All of the other pieces should be longer at 59 1/2”.
DISCARD remaining pieces of all thread.
Remove and discard any preinstalled nuts on the remaining pieces of all thread.
Step 4: Installing Center Wall
Thread the black covered all thread rods into the bottom two interior wall nut assemblies with jam nuts about ¼”. All four black covered all thread should be installed at this time. Do not start the top rods at this time.
Step 5: Installing Outer Walls
Position one outer wall insuring all thread goes through bottom corner holes. Install washer and nylon lock nut. Tighten enough to keep wall on the edge of the pallet. Final tightening will be done in a later step. NOTE: Vice grips should be used to prevent all thread from spinning while tightening nuts.
Step 6: Installing Outer Walls
Position the other outer wall insuring all thread goes through bottom corner holes. Install washer and nylon lock nut. Tighten enough to keep wall on the edge of the pallet. Final tightening will be done in a later step.
Step 7:
Thread the all thread rods into the top two interior wall nut assemblies with jam nuts about ¼”. All four all thread rods should be installed at this time.
Step 8: Caulking
Thoroughly caulk both the center wall and sidewalls the full length and depth of the groove that mates with the roof tongue. Approximately 1/2 tube per channel should be used.
Step 9: Installing Roof
Rest roof on all thread.
Pull black gasket over all thread on both sides.
Step 10a: Installing/Securing Roof
Once roof sections are in place, start the top two washer and locknuts onto the threaded rods.
Step 10b: Installing/Securing Roof
Using vice grips, hold the all thread to prevent it from moving. Tighten the locknut until the roofline starts to bow. Make sure the roof tongues are in the grooves of the walls. Repeat this for the other all thread rod. Tighten until roof has a slight visible bow. Repeat with second roof section.
Step 11:
Grind down any extra long all thread to prevent injury. (Use proper hand/eye protection) Use deep well socket to do any final tightening that may be necessary.
Step 12: Install lower doors
Align the right door hinge pin holes with the hinge pin holes in the sidewall. Slide the hinge pin tube into the aligned holes (a rubber mallet can be used to help get the pin through the holes). Repeat this step for the remaining right door and left doors.
Step 13:
Place the top edge of the roll top door into the notches of the sidewalls. (The door may need to be bowed slightly to place the edges into the notches.) Then push the door up into the track, until the entire door is in the track. Once the roll door is in the track slide it down to its closed position.
Repeat this step for the opposite side.
NOTE: Use of silicone spray along the track can make installation of the doors easier.
Step 14:
Place the black plastic caps (22) on the outside exposed threads. The Twin IBC Hard Top is now ready for use.
Write Your Own Review
