Product added to cart
Leak Control Kit
$966.00
In stock
SKU
SK0002
- The Most Advanced Leak Control Kit
- Contains various plugs and patches for smaller holes and all necessary tools and hardware for effective leak control
- Dimensions: 14″ W x 24″ L x 5″ H
Forklift-caused punctures are nothing to our most advanced Leak Control Kit.
This advanced Leak Repair Kit employs a quick-application "T" patch and proven ladder patch design to tackle an average forklift-caused puncture. The Kit also contains various plugs and patches for smaller holes and all necessary tools and hardware for effective leak control.
Each Kit Includes:
- 2 - Toggle Bolt Ball Plugs
- 6 - Toggle Bolt Surface Plugs
- 2 - T-Bolt Crack Patches
- 5 - Self-Tapping Screw Patches
- 9 - Assorted Wooden Plugs
- 1 - 8" x 12" 3/4"-thick Foam
- 1 - 8" x 12" Stainless Steel, Neoprene-Line Plate
- 1 - Hardwood Cribbing Ladder Patch
- 2 - 22' Heavy-Duty Nylon Straps
- 3 - T-Bolts with Preassembled Wingnut Washer Combo
- 1 - FIX STIX™ Epoxy
- 1 - Plug N' Dike Plug Pattie
- 1 - Lead Wool Pack
- 1 - Safety Hammer
- 1 - Hot/Cold Hose Repair Tape
- 1 - 18" x 18" Sorbent Pad
- 1 - 8" x 12" Solid Neoprene
- 1 - 22" X 22" 1/4"-thick Foam
- 1 - Steel Drift Pin
- 1 - 200' Roll of OSHA-Approved Barricade Tape
- 1 - Installation Tool Kit
- 1 - 24" X 14" X 5" Heavy-Duty Metal Carrying Case
Specifications
Dimensions : 14" W x 24" L x 5" H
Shipping Dimensions : 14" W x 24" L x 5" H
Sold as : 1 per package
Weight : 33 lbs.
Incinerable : No
UNSPSC : 47131905
Spilltech Manufacturer Part #R-Leak
| Brand | SpillTech |
|---|---|
| Type | Leak Control Kit |
| Dimensions | 14" W x 24" L x 5" H |
| Count | 1 |
| Sold As | Pack |
Identify and know the chemical you are working with and its compatibility with the materials used in this kit: Stainless Steel, Zinc Plated Steel, SBR Rubber, Neoprene
Proper protective clothing must be worn at all times!
BALL PLUGS: Used where the surface is deeply concave. Insert toggle through hole, hold outside end of bolt, slide ball firmly against hole, and tighten wing nut until leak is at its most restricted flow.
TAPER SURFACE PLUGS: Used where surface is close to flat. Apply like Ball Plugs.
“T” PATCHES: For cracks and odd holes. Use like Ball Plug except use “T” bolt to straddle crack.
SCREW PATCHES: For pinholes. Screw it in till flow stops but don’t strip out the hole trying to get it too tight.
HOT OR COLD HOSE TAPE: Pipes, hoses, small holes. Works best if surface is dry, but doesn’t have to be.
BARRIER TAPE: Mark off an area to keep bystanders out.
FIX STIX EPOXY PUTTY: Instructions in pack.
WOOD WEDGE PACK: Lay pad centered over hole, starting with bigger wedges, push as many as you can into the hole. Don’t cut the pad with the wedges. The wood and pad should swell up as liquid hits it, so try to keep them dry beforehand.
PLUG PATTIE: Simply insert putty directly on hole.
LEAD WOOL: For hairline cracks. Use sharp tool (screwdriver, knife, etc.) to pack lead into crack. Start on one end, pack more and more in until it holds, then continue along crack little by little until you get it plugged. The harder you pack it the stronger it gets. If after many tries the lead won’t stay in, the crack is too wide. Use a different item.
TWIN ‘T’ PATCH SET: Medium to large holes. Decide if you are going to use one or both ‘T’ bolts and what position they will be used. Assemble patch so it will fit the hole as on wing nut- washer – fender washer combo. After assembly, use like ‘T’ patch.
8” X 12” HARD RUBBER PATCH: Apply patch to vessel with support ladder in place, wrap straps around vessel and position over patch and ladder, then tighten.
9” X 9” NEOPRENE & 12” X 30” CLOSED CELL FOAM: For extra help where you may need it.
WOOD WEDGE & FELT KIT: Lay felt centered over hole, starting with bigger wedges, push as many as you can into the hole. Don’t cut the felt with the wedges. The wood & felt should swell up as liquid hits it, so try to keep them dry beforehand.
Write Your Own Review